Liquid manure can supply nitrogen, phosphorus and potassium, but its name tells you little about the amount in a particular load. The Ukrainian term hnoivka can refer to manure drainage, a liquid mixture of manure and water, or a liquid fraction separated from solids. Start by identifying the material. Then compare the batch analysis with what the crop and soil need. For a home garden where vegetables and greens often go straight to the table, leave fresh liquid manure or material with an unknown treatment history out of the feeding plan.

What do people mean by liquid manure?

In the narrower sense, the term refers to liquid collected where animals are kept or where manure is stored. It can include urine and liquid that drains from the manure. In farm use, the name can also refer to slurry or the liquid fraction from a separator. Check how the material is described in its records. Slurry from a system without bedding and liquid obtained after separation can carry different amounts of suspended solids and nutrients.

Ask what animals produced it, whether water entered the system, whether the solids were separated and how the batch was stored. These details matter even when the supplier has dealt with the same farm for years. A change in feed, storage or water content can change the nutrient concentrations. Two loads that look equally dark and thick may contain different amounts of nitrogen in the same volume.

Materials from a poultry house have their own properties and limits. If what you have is chicken manure, identify its source and form first. For a bedded solid material, see the separate advice on preparing horse manure. Keep the recommendation for each material tied to the form you actually have.

What to look for in a batch analysis

Ask for an analysis of the actual batch. Useful measurements include total nitrogen, ammonium nitrogen, phosphorus, potassium and moisture or dry matter. Read the date, the sample description and the units. A result per kilogram of fresh material and a result per kilogram of dry matter use different bases. If the report expresses nutrient content by mass but the delivery is measured by volume, the conversion also requires the density of that material.

Solids can settle in a storage tank. A single sample from the surface may tell you little about the material that will actually be delivered. Arrange representative sampling with the testing laboratory and staff responsible for handling the manure. Stay out of manure pits and leave agitation and pumping to trained workers. Hazardous gases can accumulate in storage areas and may be released rapidly when the liquid is disturbed.

Total nitrogen and the nitrogen available when the crop needs it are different figures. Ammonium nitrogen is available sooner than organic forms that need to mineralize. Some ammonium nitrogen can be lost as ammonia when the material is exposed to air. Use the analysis as an input to the plan. The crop, soil, timing and likely losses all affect how much useful nitrogen the crop will receive.

For phosphorus and potassium, check the form in which the laboratory reports the result. Some reports use elemental values, while recommendations or labels may show oxide equivalents. Compare like with like before adding up inputs. Also ask whether the result is for one collected sample or a representative sample of the batch. Even a precise number has limited use when it describes the wrong material or a different basis.

Protect the crop and water sources

A nutrient analysis tells you about composition. Food safety requires separate evidence. Untreated manure may contain pathogens that reach edible plant parts through direct contact, splashes, contaminated water or dirty tools. Dilution, settling and a change in smell do not verify that the material has been treated. Skip homemade fresh manure infusions for vegetables and greens you plan to harvest for food.

Pay particular attention to leafy greens, strawberries and root vegetables. The parts you eat grow close to, on or in the soil. Keep untreated material and anything with an unknown treatment history out of those beds. For a commercial crop, establish the applicable produce safety requirements for the crop, treatment and intended use. A single waiting period cannot answer every situation.

Follow the route water takes after a storm or snowmelt. A slope may lead into a ditch, a watercourse or another part of the garden. Avoid applying to flooded, waterlogged, frozen or snow-covered ground, or ahead of rainfall likely to cause runoff. If water from the area could reach a well or stream, pause the plan and establish the applicable protection measures. Check where the material would be stored too. A storage leak can send runoff along the same path.

Match the material to the soil and crop

For a garden in Ukraine, look at the condition of the ground and the forecast. A farm must also check requirements for its location and operation. After a spring thaw, a low bed can stay wet after higher ground has dried. In summer, a storm can change the same site in a short time. Check the actual zone before deciding how and when to work. If the crop will be unable to use the nutrients as planned, wait.

Start by assessing the soil in that part of the garden. Review earlier inputs, including compost and other fertilizers. If the soil already has high phosphorus, liquid manure can add more than the crop needs even while the crop still needs nitrogen. Ask an agronomist to assess a separate source for the needed nutrient using the soil test. Testing the manure does not make it a suitable match when the balance of nutrients is wrong for that bed.

Make a separate decision about adding organic matter. When that is the goal, the material and its actual dry matter content matter more than the number of buckets. Water contributes to the load volume but does not supply organic matter. If all you know is the volume and the supplier has no analysis, hold off. Ask for the composition first so you can decide whether the material serves your purpose.

If you go ahead on a suitable site, record the planned and actual amounts separately. Keep the batch report with the material name, date and location. When you next review the soil or choose another fertilizer, you will know which inputs went into that area.

A liquid fertilizer for planned feeding

Complex fertilizer for vegetables, fruit and berry crops, and flowers

Complex fertilizer for vegetables, fruit and berry crops, and flowers

DÜNGER fertilizer for vegetables, fruit and berry crops, and flowers in a 5 L canister. View the product details, choose the number of canisters and order for your vegetable garden, berry patch or flower beds.

If vegetables, berries or flowers need feeding, consider this concentrate with its declared composition and crop instructions. Follow the method and rate for the crop group in the product instructions. Liquid manure and this product have different compositions and instructions. A volume of one cannot stand in for the same volume of the other, and the concentrate serves a different purpose from an organic soil amendment.

The My Garden fertilizer calculator lets you save separate areas, their crops and measurements. If the chosen method is available in the calculator, use the information for that area to work out the amount and pack size.

Frequently asked questions about liquid manure

You also need the batch composition and units, the crop's needs and information about the soil and earlier inputs. Litres measure volume. The amount of nitrogen and other nutrients in that volume depends on the material.