The space a young thuja leaves by a fence can disappear as the hedge grows. Measure from the face of the fence to the centre of each planned tree, and allow for both the crown and the work you intend to do behind it. If the row must screen the garden and leave access for painting or repairs, those are two separate requirements. A narrow cultivar can sometimes meet both in the same strip where a wider tree would leave you with a choice between the two.
Find the width of a grown tree
Ask for the species and cultivar on the label, then look up the expected height and spread of a grown specimen. A display photograph, pot width and spacing in a nursery describe trees at one point in production. Even two plants with the same height can be quite different across the lower crown. For a privacy screen, look especially at the part that must cover the sightline. For access, work with the widest part that could reach the fence or path.
Keep the expected range if the nursery gives one. You can design for the wider figure and still meet your access goal. If the design works only when each tree stops at the smallest listed width, test another cultivar or another line. A target width for a clipped hedge calls for ongoing care, and the person who will maintain it should be able to reach its face. Find out how hard that work would be before committing to the line.
Use a tape measure and define two different distances
Start at the narrowest point between the fence and whatever is opposite it. Measure the space you need to use the path, then the space that belongs to the crown. Set the tree centres from the face of the fence, including posts that stick out. Step back to account for leaning boards, posts with thick footings and a gate that opens towards the row. For a roughly symmetrical cultivar, half the planned crown width is a first estimate of how far the branches will reach from the trunk.
If the fence adjoins a neighbouring lot, confirm the actual property boundary and the requirements that apply there separately. The example below is a physical allowance for maintaining the plants and the fence.
Imagine a crown that will be 1.2 metres across and a working strip of 0.7 metres behind it. In that sketch, a tree centre 1.3 metres from the fence gives 0.6 metres for the crown plus 0.7 metres for the strip. If the owner needs enough room for a ladder, tray or wheelbarrow, check the actual item and make the strip wider accordingly. These figures describe a sample garden, and your measured needs and verified cultivar widths supply the figures for yours.
Spacing along the row is a separate measurement from centre to centre. Set it according to the eventual screen, the cultivar and the planned clipping. Closer centres can fill the view earlier but reduce room for the trees and increase pruning work. Wider centres can keep their individual outlines and leave gaps. Decide whether you want a continuous green wall or a row of distinct crowns. The general guide to planting thuja helps with laying out and planting the row after you settle the two measurements.
Test the awkward parts of the route
Stretch a string where the centres will be. Use stakes for the trunks and mark the imagined fence-side edge of the mature crown with a second string. Open the gate fully, carry a watering can and try to pass the corner from both directions. If routine access to the fence involves changing boards from your garden, test the position needed for your shoulders and arms. Leave yourself an entrance to that route at a usable point. A corridor that ends at a locked gate or a shed is hard to benefit from.
Take a second look at changes in level. A low retaining edge may make the same tape-measure distance much less comfortable to cross. In a Ukrainian garden, think about roof or yard runoff, piles of wet snow from clearing a path, and whether water collects at posts after rain or a thaw. The fence may shade the bottom of the hedge while allowing light to the top. Walk the route on a clear day and after wet weather. You can find a more useful line by moving a short section or leaving a gate opening clear.
Look at the lower branches and leave room to trim
Young evergreen tips can be guided while they still have green growth. A row that has grown far beyond its intended outline is harder to narrow because the oldest interior wood may be bare. Stand in the available working strip and imagine reaching the full height and length you intend to clip. A solid fence or attractive permanent panel can hide that work from your view but it still occupies space. Avoid designing a screen whose back can be kept in bounds only from a neighbouring yard.
Keep the most heavily used route comfortable and plan around stationary features such as a rain barrel or outdoor tap. If you will reach the trees only from the garden side, choose the mature width first and accept that there will be less control over the other face. When planting in the foreground as well, look at what to plant between thujas by a fence before filling the clearances. Small shrubs or tall grasses can crowd a workable layout once both plantings reach size.
Bring a short list of measurements to the nursery
- Take the narrowest available width and the length of the section, along with the positions of corners and gates.
- Write down the minimum useful service and access space in your own sketch, including special tools.
- Ask for mature width and height by cultivar and estimate each crown from the trunk position on paper.
- Record whether you plan to clip or let the trees keep their individual shapes, and confirm the number of trees before ordering.
If you already bought the trees, set their pots where the stake marks are before digging. You still have the flexibility to change a centre or use a shorter row. A hole dug at each pot beforehand makes it easy to become attached to a poor layout. A small area near a gate may be more useful as an open space than as the final sliver of a hedge.
Plan an order once the row is marked
The measured strip helps you count trees and plan care after planting. If the site and growing stage indicate a need to feed, read the conifer directions for the size and age of the trees. Work out the quantity using the appropriate method on the label. A tight strip, standing water or a bare old face of the hedge calls for a separate decision.
Complex fertilizer for coniferous evergreens, granules
Save the actual number of trees in My Garden. Keep each measured height in your own notes if the height-based instructions apply. Keep the fence sketch and clearances with those notes.
Questions about thuja and fences
Measure from the face of the fence or its nearest projection to the intended trunk centre. Where fence posts protrude, mark them separately because they reduce the useful working space.
If you intend to service that side of the hedge or fence from your garden, plan a strip behind the grown crown. Test it with the tools you actually expect to bring through.
Light clipping of leafy growth can guide the outline. Cutting deep into bare old thuja wood can leave gaps, so base your plan on a width that is practical without drastic trimming.